Greenheck Fan Ventilation Hood FSD 312 User Manual

model Fsd-312  
Combination Fire smoke dampers  
APPLICATION  
Steel Airfoil Blades  
Model FSD-312 is a high performance combination fire smoke  
damper with class II leakage. High strength airfoil blades ensure the  
lowest resistance to airflow in HVAC systems with velocities to 3000  
fpm (15.2 m/s) and pressures to 4 in. wg (1 kPa) Model FSD-312 may  
be installed vertically (with blades running horizontal) or horizontally  
and is rated for airflow and leakage in either direction.  
UL 555S Leakage Class II  
UL555 112 Hour Fire Resistance Rating  
Model FSD-312 meets the requirements for fire  
dampers, smoke dampers and combination fire  
smoke dampers established by:  
RATINgs  
National Fire Protection Association  
UL 555 Fire Resistance Rating:  
NFPA Standards 80, 90A, 92A, 92B, 101 & 105  
Fire Rating:  
1½ hours  
IBC International Building Codes  
ICBO uniform Building Codes  
CsFm California state Fire marshal  
Fire Damper Listing (#3225-0981:103)  
Leakage (Smoke) Damper Listing (#3230-0981:104)  
New York City (MEA listing #260-91-M)  
Dynamic Closure Rating: Actual ratings are size dependent  
Max. Velocity:  
Max. Pressure:  
up to 3000 fpm (15.2 m/s)  
4 in. wg (1 kPa)  
UL555S Leakage Rating:  
Leakage Class:  
II  
Operational Rating:  
Max. Velocity:  
Max. Pressure:  
Actual ratings are size dependent  
up to 3000 fpm (15.2m/s)  
4 in. wg (1 kPa)  
Maximum Temperature: 350°F (177°C)- depending upon the  
“uL CLAssIFIed (see complete marking on prod-  
uct)”  
actuator  
“uL CLAssIFIed to Canadian safety standards  
(see complete marking on product)”  
Standard 555 & 555S (Listing #R13317)  
sTANdARd CONsTRuCTION  
Frame:  
5 in. x 1 in. (127mm x 25 mm)  
galvanized steel hat channel with  
reinforced corners. A low profile  
head and sill are used on sizes less  
than 17 in. (432mm)  
Greenheck Fan Corporation certifies that the  
model FSD-312 shown herein is licensed to  
bear the AMCA Seal. The ratings shown are  
based on tests and procedures performed  
in accordance with AMCA Publication 511  
and comply with the requirements of the  
Blades:  
seals:  
Double skin airfoil shape of  
galvanized steel with full length  
structural reinforcement. 14 ga.  
(2 mm) equivalent thickness.  
Extruded silicone rubber blade seals.  
Flexible stainless steel jamb seals.  
Concealed in jamb.  
AMCA Certified Ratings Programs. The  
R
AMCA Certified Ratings Seal applies to air  
performance ratings only.  
Linkage:  
Closure device:  
Axles:  
RRL 165°F (74°C)  
1
⁄2 in. (13mm) dia. plated steel.  
Bearings:  
Bronze sleeve type.  
sIze LImITATIONs:  
minimum size:  
8 in. W x 6 in. H  
(203 mm W x 152mm H)  
maximum size:  
Single Section:  
32 in. W x 50 in. H  
(813mm W x 1270mm H)  
96 in. W x 50 in. H  
(2435mm W x 1270mm H)  
128 in. W x 100 in. H  
(3251mm W x 2540mm H)  
Multiple Section:  
Vertical Only:  
LH  
OPTIONAL FeATuRes:  
H*  
• RRL/OCI (Open closed indication switches)  
• 165ºF (74°C), 212ºF (100°C), 250ºF (121°C), 350ºF (177°C) RRL’s  
available  
• TOR (remote override closure allows damper to perform smoke  
management functions during a fire emergency.)  
• Electric or pneumatic actuators to accomplish smoke  
management and system functions.  
• POC retaining angles  
W*  
RH  
• Smoke detectors  
• Momentary Switch  
Transitions (R, C, O)  
• PRV (pneumatic relief valve)  
1
*W&H dimensions furnished approximately /4 in. ( 6 mm) undersize.  
(Add sleeve thickness for overall sleeved damper dimension)  
Right hand drive is shown. Left hand drive is available upon request.  
• Security Bars  
• Sealed transitions and sleeves  
Installation instructions available at www.greenheck.com  
 
AmCA 5.2 Pressure drop  
Fsd-312  
5D  
*
36x36  
12x48  
48x12  
12x12  
24x24  
* Sizes are in inches.  
12 in. x 12 in. (305mm x 305mm)  
24 in. x 24 in. (610mm x 610mm)  
36in. x 36 in. (914mm x 914mm)  
12in. X 48 in. (305mm x 1219mm)  
48 in. x 12 in. (1219mm x 305mm)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
500  
0.03  
0.12  
0.26  
0.46  
0.72  
1.04  
1.41  
1.84  
500  
0.01  
0.06  
0.12  
0.22  
0.34  
0.49  
0.67  
0.87  
500  
0.01  
0.06  
0.12  
0.22  
0.34  
0.49  
0.67  
0.88  
500  
0.01  
0.05  
0.12  
0.21  
0.33  
0.48  
0.65  
0.85  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.02  
0.08  
0.18  
0.33  
0.51  
0.74  
1.00  
1.31  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
Greenheck Fan Corporation certifies that the  
model FSD-312 shown herein is licensed to bear  
the AMCA Seal. The ratings shown are based on  
tests and procedures performed in accordance  
with AMCA Publication 511 and comply with  
the requirements of the AMCA Certified Ratings  
Programs. The AMCA Certified Ratings Seal  
applies to air performance ratings only.  
R
 
AmCA 5.3 Pressure drop  
Fsd-312  
5D  
6D  
*
24x24  
12x12  
36x36  
48x12  
12x48  
* Sizes are in inches.  
12 in. x 12 in. (305mm x 305mm)  
24 in. x 24 in. (610mm x 610mm)  
36in. x 36 in. (914mm x 914mm)  
12in. X 48 in. (305mm x 1219mm)  
48 in. x 12 in. (1219mm x 305mm)  
Pressure Drop  
Pressure Drop  
Pressure Drop  
Pressure Drop  
Pressure Drop  
Velocity (fpm)  
(in. wg)  
Velocity (fpm)  
(in. wg)  
Velocity (fpm)  
(in. wg)  
Velocity (fpm)  
(in. wg)  
Velocity (fpm)  
(in. wg)  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.01  
0.06  
0.13  
0.23  
0.37  
0.53  
0.73  
0.95  
500  
0.01  
0.02  
0.06  
0.10  
0.16  
0.23  
0.32  
0.42  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.01  
0.02  
0.05  
0.09  
0.14  
0.21  
0.29  
0.38  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.01  
0.02  
0.06  
0.10  
0.16  
0.24  
0.33  
0.43  
500  
0.01  
0.04  
0.10  
0.18  
0.29  
0.42  
0.57  
0.74  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
Greenheck Fan Corporation certifies that the  
model FSD-312 shown herein is licensed to bear  
the AMCA Seal. The ratings shown are based on  
tests and procedures performed in accordance  
with AMCA Publication 511 and comply with the  
requirements of the AMCA Certified Ratings Pro-  
grams. The AMCA Certified Ratings Seal applies  
to air performance ratings only.  
R
 
AmCA 5.5 Pressure drop  
Fsd-312  
*
36x36  
48x12  
12x12  
12x48  
24x24  
* Sizes are in inches.  
12 in. x 12 in. (305mm x 305mm)  
24 in. x 24 in. (610mm x 610mm)  
36in. x 36 in. (914mm x 914mm)  
12in. X 48 in. (305mm x 1219mm)  
48 in. x 12 in. (1219mm x 305mm)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
Velocity  
(fpm)  
Pressure Drop  
(in. wg)  
(in. wg)  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.04  
0.18  
0.42  
0.75  
1.17  
1.68  
2.29  
2.09  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.03  
0.13  
0.29  
0.52  
0.81  
1.17  
1.60  
2.14  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.03  
0.12  
0.27  
0.48  
0.75  
1.08  
1.48  
1.93  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.03  
0.12  
0.27  
0.49  
0.77  
1.11  
1.51  
1.97  
500  
1000  
1500  
2000  
2500  
3000  
3500  
4000  
0.03  
0.14  
0.32  
0.57  
0.89  
1.28  
1.75  
2.29  
Greenheck Fan Corporation certifies that the  
model FSD-312 shown herein is licensed to bear  
the AMCA Seal. The ratings shown are based on  
tests and procedures performed in accordance  
with AMCA Publication 511 and comply with the  
requirements of the AMCA Certified Ratings Pro-  
grams. The AMCA Certified Ratings Seal applies  
to air performance ratings only.  
R
 
Application data  
damper sleeve dimensional data  
The drawings below and corresponding table show the position of the FSD-312 damper when mounted in a factory sleeve.  
The standard mounting locations provide enough space for the mounting of actuators, controls and allow space for installa-  
tion of retaining angles and duct connections.  
The standard location of a damper mounted in a  
/2" max.  
1
1
factory sleeve ("A" dimension) is shown below. The  
damper can be positioned at other locations within  
a range of 6 in. (152 mm) to 12 in. (305mm) for the "A"  
dimension.  
"A" Dimension  
in. (mm)  
33/4"  
Standard  
7 3/16 (183)  
12 (305)  
Maximum  
12 (305)  
12 (305)  
All Dampers*  
When H is 11 in. (279mm) or  
less with OCI, RRL, or TOR  
6"  
Varies  
53/8"  
*With the exception of dampers 10 in. high (254mm) or less.  
NOTE: Entire damper frame is not required to be installed within the  
wall. The damper blades, when closed should be contained within  
the wall.  
LH  
RH  
A
5"  
Sleeve Length  
T*  
Right hand drive is shown  
Left hand drive available upon request  
Actuators and Accessories  
S
space envelopes  
Externally mounted actuators always require space  
outside of the damper sleeve. The “S” dimension il-  
lustrates the clearance required for various available  
actuators.  
On dampers less than 18 in. (457mm) high, actuators  
may also require clearances above and/or below the  
sleeve. “B” and “T” dimensions are worst case clear-  
ance requirements for some dampers less than 18 in.  
(457 mm) high. All damper sizes under 18 in. (457mm)  
high do not require these worst case clearances. If  
space availability above or below the damper sleeve is  
limited, each damper size should be individually evalu-  
ated.  
B*  
B*  
T*  
Actuator Type/Model  
S
With  
With  
RRL, RRL/OCI, or TOR RRL, RRL/OCI, or TOR  
120 Volt AC  
ML-4XXX Series Honeywell  
MS-4XXX Series Honeywell  
MS-4120 Series Honeywell  
5¼ in. (133mm)  
6 in. (152mm)  
6 in. (152mm)  
¾ in.(19mm)  
3/8 in. (10mm)  
3/8 in. (10mm)  
6 in. (152mm)  
6 in. (152mm)  
6 in. (152mm)  
24 Volt AC  
ML-8XXX Series Honeywell  
MS-8XXX Series Honeywell  
MS-8120 Series Honeywell  
5¼ in. (133mm)  
6 in. (152mm)  
6 in. (152mm)  
¾ in.(19mm)  
6 in. (152mm)  
6 in. (152mm)  
6 in. (152mm)  
6 in. (152mm)  
6 in. (152mm)  
Pneumatic (25 psi min.)  
331-4551 Powers  
331-2976 Powers  
MK2-7121 Invensys  
1 in. (25mm)  
2 3/8 in. (60mm)  
3 3/4 in. (95mm)  
6¼ in. (159mm)  
12 1/8 in. (308mm)  
16½ in. (419mm)  
6½ in. (165mm)  
9¼ in. (235mm)  
10 in. (254mm)  
* For dampers 18 in. (457mm) or more in height these dimensions are 0 in. .  
 
damper sizing Information  
Dampers larger than maximum single section size are supplied as a factory assembly of two or more sections of equal size. The  
following figures show maximum damper section size and assembly configurations for multi-section dampers.  
Double Section  
Single Section  
50 in.  
(1270mm)  
50 in.  
(1270mm)  
32 in. (813mm)  
64 in. (1626mm)  
32 in. (813mm)  
Transitioned damper When a fire/smoke damper is being used in conjunction with round or oval ductwork, the  
FSD-312 can be supplied in a factory sleeve with round or oval transitions on both ends of  
the sleeve. Dampers should be ordered to the duct dimensions. Drawings below show over-  
all damper size.  
dimensions  
D*+  
2 in. (51mm) +T  
s
W*+ 2 in. (51mm)+T  
s
W*+ 2 in. (51mm)+T  
s
D*+ 2 in. (51mm)+T  
s
H*+ 2 in. (51mm)+T  
H*+ 2 in. (51mm)+T  
s
s
H*  
H*  
21/8in.  
21/8in.  
(54mm)  
These dimensions are furnished  
*
21/8in.  
(54mm)  
(54mm)  
approximately 1/4 in. (6mm) undersize,  
except round and oval dimensions  
which are approximately 1/8 in.(3mm)  
undersize.  
*
W
W*  
D*  
16 in. (406mm)  
Min.  
16 in. (406mm)  
Min.  
16 in. (406mm)  
Min.  
T
= (2)(Sleeve Thickness)  
s
TYPE R  
TYPE O  
TYPE C  
specifications  
Combination Fire Smoke Dampers meeting the following specifica-  
tions shall be furnished and installed where shown on plans and/or  
as described in schedules. Dampers shall meet the requirements of  
NFPA 80, 90A, 92A, 92B, 101 & 105 and further shall be tested, rated  
and labeled in accordance with the latest edition of UL Standards  
555 and 555S. Dampers shall have a UL555 fire rating of 1½ hours  
and be of low leakage design qualified to UL 555S Leakage Class II.  
be galvanized steel formed into a structural hat channel shape with  
reinforced corners. Bearings shall be sintered bronze sleeve type  
rotating in extruded holes in the damper frame. Blade edge seals  
shall be silicone rubber designed to inflate and provide a tighter seal  
against leakage as pressure on either side of the damper increases.  
Jamb seals shall be stainless steel compression type. Blades shall  
be completely symmetrical relative to their axle pivot point, present-  
ing identical resistance to airflow in either direction or pressure on  
either side of the damper.  
Each damper/actuator combination shall have a UL555S elevated  
temperature rating of 250° F (121°C) minimum and shall be opera-  
tional and dynamic rated to operate at maximum design air flow at  
its installed location. Each damper shall be supplied with an appro-  
priate actuator installed by the damper manufacturer at the time of  
damper fabrication. Damper actuator shall be (specifier select one  
of the following) electric type for 120 (24 or 230) volt operation or  
pneumatic type for 25 psi minimum (30 psi maximum) operation.  
Damper must be rated for mounting vertically (with blades running  
horizontal) or horizontally and be UL 555S rated for leakage and  
airflow in either direction through the damper. Each damper shall be  
supplied with a 165°F (74°C) RRL. Testing and ratings to be in ac-  
cordance with AMCA standard 500-D.  
The basis of design is Greenheck Model FSD-312.  
Damper blades shall be of the double skin airfoil type and shall  
have an equivalent thickness of 14 ga. (2mm) . Damper frame shall  
Copyright © 2006 Greenheck Fan Corporation  
FSD-312 Rev 3 June 2006  
 

GPX Stereo System HM102B User Manual
Graco Car Seat CLASSIC CONNECT 30 User Manual
Graco Car Seat PD268712B User Manual
Graco Inc Paint Sprayer 230975 User Manual
Grizzly CD Player H5524 User Manual
Grizzly Trimmer H5503 User Manual
Harbor Freight Tools Nail Gun 41209 User Manual
Harbor Freight Tools Welder 97503 User Manual
HP Hewlett Packard Laptop TX2500 User Manual
Husqvarna Blower 2345 XLS User Manual